TF-Luna LiDAR Range Finder Sensor Module 1.25mm-6Pin Male Connector to Male/Female Dupont Cable with WiFi LoRa 32 V2 0.96" Oled Wifi BLE Transceiver Module

TF-Luna LiDAR Range Finder Sensor Module 1.25mm-6Pin Male Connector to Male/Female Dupont Cable with WiFi LoRa 32 V2 0.96" Oled Wifi BLE Transceiver Module
Click image for Gallery
  • Brand: DIYmall
  • Product Code: TF0004+FZ2886+FZ2904A+FZ2904B TF-Luna LiDAR with WiFi Lora 32 V2
  • Availability: In Stock
  • $48.99
  • Ex Tax: $48.99
  • Price in reward points: 4
  • 2 or more $47.99
  • 5 or more $46.99
- +



Tags: Benewake, TF-Luna, Lidar, Range Finder Sensor, 1.25mm to dupont cable, WiFi Lora 32 V2, WiFi Lora32, Lora_wifi, 0.96" OLED Display, ESP32 wifi ble module

Benewake TF-Luna LiDAR Range Finder Sensor Module 8m with 1.25mm-6Pin Plug Cable


Description:
Operating range: 0.2m~8m
Accuracy: ±6cm@(0.2-3m), ±2%@(3m-8m)
Measurement unit:cm
Range resolution: 1cm
FOV: 2°3
Frame rate: 1~250Hz( adjustable )4
Supply voltage: 5V±0.1V
Average current: ≤70mA
Peak current: 150mA
Average power: 350mW
Communication level: LVTTL(3.3V)
Communication interface: UART/IIC
Default baud rate: 115200
Data bit: 8
Stop bit: 1
Parity check: None
Light source:VCSEL
Wavelength:850nm
Operating temperature : -20°C~75°C
Certification:CE,FCC,ROHS

0.96 OLED Display ESP32 WIFI Bluetooth Lora Development Board Transceiver SX1276 868MHZ 915MHZ IOT


Description:
Main chip: espressif esp32 and SX1276
Operating voltage: 3.3V to 7V
Flash:32M-Bits
Main Frequency:240MHZ
Support frequency:868-915MHZ
Lora chip:SX1276
Distance: about 2.8KM in open place
Computing power: 600DMIPS
Dual-mode Bluetooth: traditional Bluetooth and BLE low-power Bluetooth
Development environment: support arduino
USB adapter chip: cp2102
Operating temperature range: -40 ° C to + 90 ° C
Support modes: Sniffer, Station, softAP and Wi-Fi Direct
Data rate: 150 Mbps @ 11n HT40,72 Mbps @ 11n HT20,54 Mbps @ 11g, 11 Mbps @ 11b
Transmit power: 19.5 dBm @ 11b, 16.5 dBm @ 11g, 15.5 dBm @ 11n
Receiver sensitivity up to - 98 dBm
UDP continues to throughput by 135 Mbps


Wiring diagram:
TF-Luna  ------WiFi LoRa 32 V2
5V ------ 5V
Lidar RX ------ PIN 23 TXD
Lidar TX ------ PIN 22 RXD
GND ------ GND

Note: Before you test it in Arduino IDE, make sure that your IDE has installed Heltec ESP32 Series Dev-boards in your Board Manager and have installed Heltec ESP21 Dev-Boards in your sketch.

Package Included:
1 X TF-Luna LiDAR Range Finder Sensor Module
1 X WiFi Lora 32 V2 0.96" oled module
1 X 1.25mm-6Pin male to male connector Plug cable
1 X 1.25mm-6Pin male connector to male Dupont Cable
1 X 1.25mm-6Pin male connector to female Dupont Cable

Write a review

Note: HTML is not translated!
    Bad           Good

Related Products