Upgraded LoRa32u4 II Lora Development Board LiPo Atmega328 SX1276 HPD13 915MHz 868MHZ with SHT31 LIS3DHTR Sensor With IPEX to SMA Antenna

Upgraded LoRa32u4 II Lora Development Board LiPo Atmega328 SX1276 HPD13 915MHz 868MHZ with SHT31 LIS3DHTR Sensor With IPEX to SMA Antenna
Click image for Gallery
  • Brand: DIYmall
  • Product Code: DIY0078+FZ2865+FZ1283-upgradedLoRa32u4 II with IPEX antenna
  • Availability: In Stock
  • $20.99
  • Ex Tax: $20.99
  • Price in reward points: 3
  • 2 or more $19.49
  • 5 or more $18.49
  • 10 or more $17.49
  • 20 or more $16.49
- +

Tags: LoRa32u4 II, Lora Development Board, LORA Module, SHT31, LIS3DHTR

Comparing the standard one, this version add some sensors as below:
First is Temperature Humidity Sensor
Second is  Light Sensor
Third is secure element, to secure data exchange and prevent product copy
Last is accelerometer, to detect motion on 3 axis

LoRa32u4 II is a light and low consumption board based on the Atmega32u4 and HPD13  915MHz LoRA module and an USB battery charging circuit. Ideal for creating long range wireless networks that can exceed 2.4 GHz 802.15.4 and similar, it is more flexible than Bluetooth LE, does not require high power unlike WiFi and offers long range.
The ATmega32u4 is clocked at 8 MHz and 3.3 V. This chip has 32 K of flash, 2 K of RAM and built-in USB to Serial communication, debugging and programming capabilities without the need for an external FTDI chip, it can also act as an HID device (mouse, keyboard, USB MIDI device, etc).
This board is also equipped with a LiPo and Liion charging circuit and a standard battery interface. It is fully compatible with Arduino. A white user led is tied to pin 13. An orange LED is used for charging status.

HPD13 wireless module, using high-performance, highly integrated RF transceiver chip SX1276 design. Advanced LoRaTM spread spectrum communication technology to ensure that the module communication distance and anti-jamming capability greatly improved, and also achieved a very low current consumption. In the LoRaTM mode, the HPD13 provides higher reception sensitivity performance, more robust anti-jamming capability, and improved communication distance and reliability compared to the same transmit and receive modules on the market. In normal (G) FSK mode, it also provides industry-specific receiver sensitivity, as well as very high communication rates.  

ATmega32u4 @ 8MHz with 3.3V logic/power
3.3V regulator with 500mA peak current output
USB native support, comes with USB bootloader and serial port debugging
Built in 100mA lipoly charger with charging status indicator LED
Reset button

Receive current: 10 ~ 14mA
Interface Type: SPI
Operating temperature: -40 ° C to + 85 ° C
Digital RSSI function
Automatic frequency correction
Automatic gain control
Radio wake-up function
Low voltage detection and temperature sensor
Fast wakeup with frequency hopping
Highly configurable packet handlers

LoRa32u4II revision 1.3 improvements :

1.1.    The battery monitoring circuit is now active and enabled by the previously unused pin PB0 (not broken-out on headers), it must be enabled (high) to allow battery monitoring.
1.2.    The battery charger is now controlled, it must be enabled (high) by PB0 to allow battery charging.
1.3.    The LDO has been replaced for an ultra low IQ LDO (0.5uA).
1.4.    Overall sleep current has been lowered from 260.2uA to 183.8uA (tested with Atmega32u4 in watchdog sleep mode @ 8MHz and LoRa circuit in sleep mode).

2.    USAGE
2.1.    LoRa DIO1 is now connected by default to Atmega32u4 pin 5 (PC6) allowing direct use of LMIC and other LoRaWAN libraries without soldering, it is still possible to disable this link by opening the DIO1 solder jumper on topside.
2.2.    LoRa DIO2 and DIO3 are now routing to Atmega32u4 pin 6 (PD7) and 14 (PD5), solder jumpers are open by default (these DIO pins are rarely used).
2.3.    Atmega32u4 pins 0 (PD2),1 (PD3) for UART and 2 (PD1), 3 (PD0) for I2C are now free for use.
2.4.    LoRa DIO pins solder jumpers have been moved on topside for better accessibility.
2.5.    Pull-up resistors (4.7K) have been added on the I2C bus.
2.6.    The antenna uFL connector has been moved on topside to ease access.

3.1.    High precision ultra low power I2C temperature / humidity sensor Sensirion SHT30 has been added as an option.
3.2.    High precision ultra low power I2C ambient Light sensor ROHM BH1750 has been added as an option.
3.3.    Secure element Atmel ATSHA204 CryptoAuthentication chipset has been added as an option on Atmega32u4 pin 13 (PC7, shared with user LED), it provides encryption, secured eeprom and allows secure authentication, secure boot, copy protection, encrypted communication etc.
3.4.    High precision ultra low power I2C accelerometer ST MicroElectronics LIS3DHTR with interrupt routing to Atmega32u4 pin 14 (PD5, shared with LoRa DIO3), this routing is done via a solder jumper on bottom (open by default).

Document link: http://www.diymalls.com/files/DIY0050-DIY0051-LORA32U4.zip

Description for the Atenna:
Type: U.FL to Female SMA
Impedance: 50 ohms
Gain: 2DBi

Package includes:
1 X LoRa32U4 II Lora Module V1.3 Upgrade version

1 X IPEX to SMA Antenna 850-1850MHz

1 X   JST-PH2.0MM-2P Cable

Write a review

Note: HTML is not translated!
    Bad           Good

Related Products