ESP32 Programming Module Test Board Burning Fixture Micro USB interface onboard CP2102 Chip
This is ESP32 burning fixture, makes the ESP32 programming very easy and simple. Support for ESP-23/ESP-32D/ESP-32U etc.
Kindly note that it only works with SMD chips/chip module, can not work with implementing whole module like NodeMCUs or other development board.
How to program?
1, Download the flash tool from espressif and also install CP2102 driver if you haven't install it before. Here is the link for the Flash Download Tools: https://www.espressif.com.cn/en/support/download/other-tools
2, Open the flash download tool, and choose ESP32. Fill in the bin file address in SPIdownload.
3, The Flash config will be filled automatically, no need to choose. If not due to different version, you need set the flash config firstly.
4, Choose the COM port, and baud rate. If the baud rate you choose too big, you may fail to flash, in this case, you need choose a small baud rate.
5, Click "Start", and it starts to flash. If you failed to flash it, pls click "Stop" firstly, and check for baud rate, then re-click "Start".
Note: Please make sure the chip module is seated properly in the programmer before you flash the new firmware!
ESP32-WROOM-32 Chip Module ESP-32S WIFI BLE Module IOT Dual Core CPU with Low Power Consumption MCU Built-in Antenna
Xtensa 32-bit LX6 Dua-core processor, up to 600 DMIPS.
448 KByte ROM
520 KByte SRAM
16 KByte SRAM in RTC.
QSPI can connect up to 4* Flash／SRAM, each flash should be less than 16 Mbytes.
Supply Voltage: 2.2V-3.6V
802.11 n (2.4 GHz), up to 150 Mbps
802.11 e: QoS for wireless multimedia technology.
MPDU and A-MSDU aggregation
Fragmentation and defragmentation
Automatic Beacon monitoring/scanning
802.11 i security features: pre-authentication and TSN
Wi-Fi Protected Access (WPA)/WPA2/WPA2-Enterprise/Wi-Fi Protected Setup (WPS)
Infrastructure BSS Station mode/SoftAP mode
Wi-Fi Direct (P2P), P2P Discovery, P2P Group Owner mode and P2P Power Management
UMA compliant and certified
Antenna diversity and selection
Compliant with Bluetooth 4.2 BR/EDR and BLE specification
Class-1, class-2 and class-3 transmitter without external power amplifier
Enhanced power control
+10 dBm transmitting power
NZIF receiver with -98 dBm sensitivity
Adaptive Frequency Hopping (AFH)
Standard HCI based on SDIO/SPI/UART ? High speed UART HCI, up to 4 Mbps
BT 4.2 controller and host stack
Service Discover Protocol (SDP)
General Access Profile (GAP)
Security Manage Protocol (SMP)
Bluetooth Low Energy (BLE)
All GATT-based profile supported
SPP-Like GATT-based profile
A2DP/AVRCP/SPP, HSP/HFP, RFCOMM
CVSD and SBC for audio codec
Bluetooth Piconet and Scatternet
12-bit SAR ADC up to 18 channels
2 × 8-bit D/A converters
10 × touch sensors
4 × SPI，2 × I2S，2 × I2C，3 × UART
1 host (SD/eMMC/SDIO)，1 slave (SDIO/SPI)
Ethernet MAC interface with dedicated DMA and IEEE 1588 support
Motor PWM，LED PWM up to 16 channels
Ultra low power analog pre-amplifier
IEEE 802.11 standard security features all supported, including WFA, WPA/WPA2 and WAPI
1024-bit OTP, up to 768-bit for customers
Cryptographic hardware acceleration: - AES - HASH (SHA-2) library - RSA - ECC - Random Number Generator (RNG)
SDK Firmware for fast on-line programming
Open source toolchains based on GCC
1 X ESP32 Programming Module Burning Fixture
5 X ESP32-WROOM-32 Chip module