ESP8266 Flash Downloader Module Burning Fixture Development Board for ESP-01S ESP-12F ESP-07S ESP-12S ESP-F FZ3489

ESP8266 Flash Downloader  for ESP-12F ESP-07S ESP-12S ESP-F FZ3489

Description:
Compatible with ESP-01S ESP-07 ESP-07S ESP-12E ESP-12F ESP-12S ESP-F
Micro USB interface
Very easy to program modules

All IO ports have been drawn out and can be used as ZUI small system development board or small batch burning fixture. The board supports one-click firmware download function, and add burning

Mode indicator (blue LED) and serial communication indicator (green LED).

ESP8266 ESP-F Serial Wireless WiFi Transmission Module FZ1734D

Introduction
ESP-F is encapsulated  by the high performance chip ESP8266EX. The chip is encapsulated a advanced Tensilica’s L106 32-bit MCU, with 16-bit short mode, basic frequency support 80 MHz, 160 MHz, supports RTOS. ESP8266EX has the full and complete WiFi fuction, which can used independently and alsoused as a slaver with other Hoster MCU, which can start directly from the out-built Flash. In addition, the built-in high-speed buffer is benefit for the system performance. Especially, ESP8266EX can be used as a WiFi adapter by SPI/SDIO and/or I2C/UART interface, when it is applied to the other MCU design.
 
SOC characteristics
Built-in Tensilica L106 ultra-low power 32-bit CPU, main frequency supports 80MHz and160MHz, and RTOS;
Built-in TCP/IP protocol;Built-in one-channel 10-bit high precision ADC;Outboard interface: HSPI, UART, I2C, I2S, IR Remote Controk, PWM, GPIO;Deep sleep current is 10uA, the cut-off current is smaller than 5uA;Wake,connect and transmission data package within 2ms;The consume power is smaller 1.0Mw (DTIM3) when at stand by status;Built in 1M byte for SPI Flash.
WiFi characteristics
Support 802.11 b/g/n/e/I;Support Station, Soft AP, Soft AP+STA mode;Support WiFi Direct (P2P);Support CCMP (CBC-MAC, computation mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC etc., for hardware acceleration.
P2P finding, P2P GO mode/ GC mode and P2P power manageWPA/PA2PSK and WPS;802.11 security certification: pre-certification and TSNSupport 802.11n (2.4GHz);802.1h/RFC1042 frame encapsulation;Support seam less roaming;Support AT remote update and cloud update (OTA);Support Smart Config function (including Android and Ios device).

Module interface
2x UART
1 x ADC
1 x En
1 x wakeup pin
1 x HSPI
1 x I2C
1 x I2S
More than 10 GPIOs
4M bytes of SPI Flash
Working temperature: -40℃-+125℃;
Module size: 16mm×24mm

ESP8266 ESP-01S 4MB WiFi Module FZ2400-4MB

 About program: Please choose  "Generic ESP8285 Module" board in Arduino IDE  to program it.

Description:
comparing to esp-01, esp-01s has these advantages:
The PCB layout has changed for an improvement in WiFi radio performance
4MB Flash Memory...upgraded from 512KB
Latest version esp-01s,with stronger signal

Feature:
    SDIO 2.0, SPI, UART
    32-pin QFN package
    Wi-Fi Direct (P2P), soft-AP
    Integrated TCP/IP protocol stack
    Integrated TR switch, balun, LNA, power amplifier and matching network
    Integrated PLLs, regulators, DCXO and power management units
    +19.5dBm output power in 802.11b mode
    Power down leakage current of <10uA
    Integrated low power 32-bit CPU could be used as application processor
    SDIO 1.1/2.0, SPI, UART
    STBC, 1×1 MIMO, 2×1 MIMO
    A-MPDU & A-MSDU aggregation & 0.4ms guard interval
    Integrated RF switch, balun, 24dBm PA, DCXO, and PMU
    Integrated RISC processor, on-chip memory and external memory interfaces
    Integrated MAC/baseband processors
    Quality of Service management
    I2S interface for high fidelity audio applications
    On-chip low-dropout linear regulators for all internal supplies
    Proprietary spurious-free clock generation architecture
    Integrated WEP, TKIP, AES, and WAPI engines

Specification:
    802.11 b/g/n
    Wake up and transmit packets in < 2ms
    Standby power consumption of < 1.0mW (DTIM3)

Document link: https://nurdspace.nl/ESP8266

Package included:

1 X ESP8266 Flash Downloader Module FZ3489